Intelligent Detectors |
 |
Photoelectric
Smoke Detector (58000-650ADV)
The AX Photoelectric Smoke Detector is suitable for slow burning or smoldering fires and should be positioned where these are most likely to occur. They can be set to a sensitivity mode via the AX range of control and indication equipment which best suits the application..
|
 |
Heat
Detector (58000-450ADV)
The AX heat detector, distinguishable by the low airflow resistant case, uses a single thermistor to sense the air temperature around the detector. This type of detector is particularly useful where the environment is dirty or smokey under normal conditions. Range is 135F to 200F. Mode setting are either Static/Rate of Rise or Static only. |
 |
Multi Sensor Detector (58000-750ADV)
The AX multi-sensor detector utilizes both photoelectric and thermal sensing technologies to monitor two types of fire signatures: smoke and heat. The built-in microprocessor processes the two signals according to the response mode selection. Each sensing technology can be monitored independently by the AX panels. |
 |
Ionization
Smoke Detector (58000-550ADV)
The AX Ionization detector is suitable for fast burning, flaming fires and should be positioned where these are most likely to occur. They can be set to a sensitivity mode via the AX range of control of control and indication equipment which best suits the application.
|
 |
Intelligent Loop Powered Beam Detector (55000-266ADV)
This SLC loop driven device comprises a transmitter, a receiver, an interface and optionally, one or more reflectors. The beam detector is designed to protect large and open spaces such as atriums, museums, warehouses and factories. The transmitter and receiver are designed to be fitted on opposite walls approximately 1ft to 2ft below the ceiling and they can protect areas up to 300ft long and 45ft wide, a total of 13,500ft². |
 |
Intelligent Air Duct Detectors (AX-SL-DAA-P/N, AX-SL-DAA4R-P/N)
Used to detect smoke and products of combustion in air moving through HVAC duct work. The units are designed to prevent the recirculation of smoke by air handling systems. The units come with either an intelligent Photo or Ion smoke detector and operate in duct widths of 6” to 10’ wide with an air velocity between 100 and 4,000 feet per minute. Come in both 2 wire and 4 wire versions. |
Detector Mounting Bases |
 |
E-Z Fit Base (45681-250ADS)
Designed for mounting flexibility, the E-Z Fit Base attaches to the screws of an electrical box, then after tightening, the screws are hidden by unique hinged covers. Bases enable easy to install “one way” only detector attachment without need for force. For added protection, detectors can be locked to the base via a built-in mini-hexagonal screw. |
 |
Relay Base (45681-242ADS)
The Relay Base mounts to a 3” octagonal electrical box and incorporates a sub-addressable remote LED output and Form “C” relay contact. The relay receives operating power from the AX Panel’s SLC loop, no extra 24 volt power is required. It can be separately controlled by the panel’s Control-By-Event program.
|
 |
Multi-Flex Sounder Base (MB-SDRT-AA)
The Multi-Flex Sounder Base provides selectable steady or temporal signal pattern output with low or high volume settings. The base mounts to 4” octagonal or 4” square electrical boxes. Separate 24 volt input required.
|
 |
Loop Isolator and Isolating Detector Bases (55000-750ADV, 45681-321ADV)
Loop Isolators protect groups of devices from short circuits on the SLC loop, whereas the Isolating Detector Bases protect individual detectors on the SLC loop from short circuits. Both bases contain a yellow LED that illuminates when it detects a short circuit.
|
 |
Loop Powered Sounder Beacon Base (45681-525ADS, 45681-526ADS)
Powered from the AX Panel’s SLC, these bases provide synchronized “steady” or “ANSI Temporal” tones as well as a flashing red or amber beacon upon alarm activation. Two volume settings are dip switch selectable.
|
|
Loop Powered Enhanced Sounder Beacon Base (45681-527ADS, 45681-524ADS)
Powered from the AX Panel’s SLC, these bases provide fifteen (15) synchronized tones as well as a flashing red or amber beacon. In addition, seven (7) different sound levels may be selected. Tones, beacon and volume outputs are each individually selectable and controlled by the AX Series Fire Panels.
|
 |
Intelligent Pull Stations (AX-APS2-F1, AX-APS2-F2)
The AX Series Intelligent Manual Pull Stations are made of rugged die cast metal for long life and durability. They come with a built-in red LED that turns on steady in alarm and also come with a built-in Form C contact. The stations come in either single or dual action configuration, and contain a toggle switch which is ideal for system testing and servicing.
New York City versions are available: (AX-APS2-F1NYC, AX-APS2-F2NYC)
|
Intelligent Input/Output Modules |
 |
Mini Priority Switch Monitor Module (55000-830ADV)
Designed to monitor the state of one or more Normally Open or Normally Closed contacts connected onto Class A or B wiring. Reports open and ground-circuit troubles on the sub-circuit (IDC). The device incorporates an interrupt facility to give the fastest response to the AX Series Fire Panels. The product is designed to fit into a single-gang electrical box and contains a built-in red alarm LED. |
|
Mini Switch Monitor Module (55000-831ADV)
Designed to monitor the state of one or more Normally Open or Normally Closed contacts connected onto Class A or B wiring. Reports open and ground-circuit troubles on the sub-circuit (IDC). The product is designed to fit into a single-gang electrical box and contains a built-in red alarm LED. |
 |
Switch Monitor Module (55000-805ADV) / AX Dual Switch Monitor Module (55000-790ADV)
Designed to monitor the state of one or more Normally Open or Normally Closed contacts connected onto Class A or B wiring. The AX Switch Monitor Module incorporates a single IDC circuit and the Dual Switch Monitor Module incorporates two (2) independent IDC circuits. Reports open and ground-circuit troubles on the sub-circuit (IDC). The product is mounted on a plastic mounting plate for use with a 4” electrical box. |
 |
Priority Switch Monitor Module (55000-806ADV)
This product has the same functionality as the standard AX Switch Monitor Module, but incorporates a priority interrupt facility to give the fastest response to monitored devices wired to the IDC circuit. The product is mounted on a plastic mounting plate for use with a 4” electrical box. |
 |
NAC Control Module (55000-825ADV)
This module incorporates an independent, individually programmable, Notification Appliance Circuit (NAC). Each NAC module allows switching of an external power supply or audio amplifier to a group of notification appliances such as horns, bells, strobes, speakers, etc. The module incorporates a synchronization facility which allows the outputs of groups of modules to be synchronized by commands from the AX Series Fire Panels. The product is mounted on a plastic mounting plate for use with a 4” electrical box. Class A or B wired circuit. |
 |
I/O Relay Output and Switch Monitor Module (55000-820ADV)
This module provides a single initiating device circuit (IDC) input, an independently controlled Form-C Relay contact output and an optically isolated voltage input. The IDC can be wired in Class A or Class B configuration. The relay is rated 24 VDC @1 Amp. The optically isolated voltage input is for special application purposes. The module mounts to a 4” electrical box. |
 |
120 VAC I/O Module (55000-859ADV)
This module contains a 4 Amp @120VAC/30VDC relay along with an IDC input circuit. Ideal for switching on motors and fan dampers while monitoring successful opening and closing of damper doors. Module mounts in 4” electrical box. |
 |
DIN Rail Mounted Mini Switch Monitor Module(55000-765ADV)
This module can be mounted to a 1 3/8” DIN rail track, and contains 3 built-in LEDs: Red for Alarm, Green for Device Polling and Amber for Trouble indication. It also has a remote LED output that flashes during polling and goes steady during an alarm condition. It contains a single initiating device circuit (IDC) that can be configured for either alarm or pre-alarm activation. |
